homeaboutcontacttestimonialsregistercourse scheduleblog            
CCNA: Classful Subnetting


February 16, 2009
By Jeff Ratchford, CCNA, CCNP, CCVP, CCSI# 21763

For a pdf of this article: Classful Subnetting

If there is a secret to the Cisco CCNA test, it is the ability to subnet quickly and accurately. In this article I will discuss classful
subnetting. Once a person has a good grasp on this process, the other components of subnetting become much easier.

Consider classful subnetting to be a six step process:

1. Convert the required number of subnets to binary and count the number of binary bit positions needed to represent the

2. Append the number of bit positions obtained from step 1 to the given mask and then express the new mask in dotted
decimal notation.


3. Verify there are enough host bits left for the required hosts. We use the formula (2^x)-2, where x is the number of

remaining host bits in the new mask (the zeroes).


4. Calculate any growth available in network IDs. We use the formula (2^x), where x is the number of added mask bits. This

is the value calculated from step 1.


5. List the first few network IDs that result. To perform this step, remember the phrase, ‘the first network ID is the decimal
value of the low-order mask bit’. This is actually the block size of the mask and is also the first available subnet that is
available if subnet-zero is disabled. If subnet zero is enabled (it is by default) then the very first subnet is this ‘first network
ID’ minus this block size.


6. List the first and last host on one or two of the network IDs. To get the first host IP address we simply add one to the
network ID. The last host address on a subnet will always be two less than the next subnet. The broadcast address for a
subnet is always one less than the next subnet.


Let’s work through an example. We are given a class B network of We decide we need to subnet this into at least
100 subnets, each having at least 100 hosts.


When we do step one, we see that we need seven significant bits to represent the decimal value of 100 (1100100).


Appending these seven bits to the given 16 bit mask gives us a new mask of 23 bits (

The new mask has 9 remaining host bits (the zeroes of the mask), giving us 510 possible hosts per subnet (2^9)-2.


Step four gives us 2^7=128 possible subnets. We assume that subnet-zero is allowed, therefore we do not need to subtract any
unusable subnets (the all zeroes and the all ones subnet).


In step 5 we list the first available subnets. The new mask in the third octet has the following bit pattern: 11111110. We know from
our binary math studies that the associated decimal value of each of these bits is: 128 64 32 16 8 4 2 1. Looking at the phrase
‘decimal value of low-order mask bit’ we see the decimal value is 2 in the third octet. This is also our block size. Based upon the
given of, our first available subnet is if subnet zero is off. With subnet zero on we subtract the block size
of 2 in the third octet and we get as the first available subnet (subnet-zero) and the second subnet is
Each successive subnet is always a multiple of our block size. To get the tenth network after the ‘block size’ network we multiply
10 by the block size of 2 and get


Looking at subnet we see that the first host IP is Based upon the next subnet of, the
broadcast address of the subnet is, which is the last available address before you reach the next
subnet of The last available host IP on the subnet is, which is two less than the next
available network id of




375 N. Stephanie Street, Bldg 21 Suite 2111 Henderson, NV 89014
Website: www.ccbootcamp.com Phone: 877.654.2243

For questions or comments about this article please email sales@ccbootcamp.com

CC Bootcamp Twitter
CC Bootcamp Linkedin
Pearson Vue
CONTACT US | TOLL FREE: 1.877.654.2243 or 1.877.NLI.CCIE | INTERNATIONAL: +1.702.968.5100
©2010 Network Learning, Inc. All Rights Reserved.